Reload systemd # systemctl --system daemon-reload ALSA channels mute when headphones are plugged/unplugged improperly If when you unplug your headphones or plug them in the audio remains muted in alsamixer on Last edited by infestator (2011-06-25 14:28:31) Offline #10 2011-10-04 07:36:13 developej Member Registered: 2011-10-02 Posts: 68 Re: Pulseaudio No sound Same problem. then run pax11publish -r command then could be also good to logout and login again. Failed to create sink input: sink is suspended If you do not have any output sound and receive dozens of errors related to a suspended sink in your journalctl -b log, http://da4design.com/arch-linux/arch-linux-dns-not-working.php
Under the Output Devices tab, you should see the local and remote output devices. If you configured in default.pa to load and use the OSS modules then check with lsof that /dev/dsp device is not used by another application. This can be resolved temporary by: $ echo 100000 > /proc/sys/fs/inotify/max_user_watches For permanent use save settings in the 99-sysctl.conf file: /etc/sysctl.d/99-sysctl.conf # Increase inotify max watchs per user fs.inotify.max_user_watches = 100000 default.pa This file is a startup script and is used to configure modules. https://wiki.archlinux.org/index.php/PulseAudio/Troubleshooting
First, identify the card you want its channels swapped: $ cat /proc/asound/cards and use the name string for the device you wish to use (the one in square brackets, e.g. [Intel]). To use it, find your headphones with: $ pacmd list-sinks | grep -e 'name:' name:
module-jackdbus-detect.so dynamically loads and unloads module-jack-sink and module-jack-source when jackdbus is started and stopped. Stop Pulse, erase the "stream-volumes" in ~/.config/pulse and/or ~/.pulse and restart Pulse. Selecting an output device from the list will allow the audio stream to be switched to the PulseAudio server associated with that output device. Pulseaudio No Sound It takes a protocol prefix like unix: or tcp followed by the path or IP of the server.
See PulseAudio/Examples#TODO[broken link: invalid section] for a complete example. Outputs by PulseAudio error status check utilities If the pax11publish -d shows error like: N: [pulseaudio] main.c: User-configured server at "user", refusing to start/autospawn. The properties: application.name and application.process.binary, among others, should help here. This leads to no sound coming from HDMI output.
Cannot update configuration of sound device in pavucontrol pavucontrol is a handy GUI utility for configuring PulseAudio. Pulseaudio-alsa The audio routing and processing tasks are all handled by various modules, including Pulse's native protocol itself (provided by module-native-protocol-unix). Alternatively, you can use pavucontrol to do this: make sure you have set up the display to "All input devices", then select "Monitor of [your sound card]" as the recording source. Setting the sound card's sampling rate into PulseAudio configuration (3/5) The default sampling rate in PulseAudio: $ grep "default-sample-rate" /etc/pulse/daemon.conf ; default-sample-rate = 44100 44100 is disabled and needs to be
Calculate your fragment size in msecs and number of fragments (2/4) PulseAudio's default sampling rate and bit depth are set to 44100Hz @ 16 bits. https://wiki.archlinux.org/index.php/PulseAudio/Configuration To just try PA on top of JACK, have PA load the necessary modules on start: pulseaudio -L module-jack-sink -L module-jack-source To use PulseAudio with JACK, JACK must be started before Restart Pulseaudio Arch This also resets application volumes. 3. Arch Linux No Sound They both should produce sound simultaneously.
XMMS2 Make it switch to pulseaudio output $ nyxmms2 server config output.plugin pulse and to alsa $ nyxmms2 server config output.plugin alsa To make xmms2 use a different output sink, e.g. More about the author PulseAudio will automatically create new configuration files on its next start. The daemon itself uses a plain simple static configuration that uses your configured pcm.!default ALSA devices and nothing more. This is much less hassle than it used to be (in this example, we are using GNOME desktop). Arch Linux Alsa
It is replaced by pasystray The following example could be used and modified as necessary as a startup script that daemonizes PulseAudio and loads the padevchooser program (optional, needs to be It can be used to set the configure the default sink and source statically as well as allowing (or disallowing) clients to automatically start the server if not currently running. Add a remap rule to /etc/pulse/default.pa, use the name you found with the previous command, here we will use alsa_input.pci-0000_00_14.2.analog-stereo as an example: /etc/pulse/default.pa ### Remap microphone to mono load-module module-remap-source http://da4design.com/arch-linux/arch-linux-touchpad-not-working.php Content is available under GNU Free Documentation License 1.3 or later unless otherwise noted.
For example, raising the VoIP call volume will raise the hardware volume and adjust the music-player volume so it stays where it was, without having to lower the volume of the Pulseaudio Gui beep works in the console, but no other audio works. kdeplasma-applets-veromixAUR[broken link: archived in aur-mirror] An advanced PulseAudio applet for KDE.
Edit /etc/pulse/default.pa, and change the following region: ### Load audio drivers statically (it is probably better to not load ### these drivers manually, but instead use module-hal-detect -- ### see below What is the meaning of "cow in the middle"? With this configuration, the bit rate we need is 44100*16 = 705600 bits per second. Pulseaudio Daemon Startup Failed Since environment variables cannot be modified after child processes are started , X11 properties are more flexible because they are more easily changed because they are globally shared.
alsa_output.pci-0000_00_1b.0.analog-stereo.monitor). To allow for chrooted apps to access the pulse server, the following directories must be mounted within the chroot:- /run /var/lib/dbus /tmp ~/config/.pulse /dev/shm should also be mounted for efficiency and Taste is the enemy of creativeness.PicassoPerfection is reached, not when there is no longer anything to add, but when there is no longer anything to take away.Saint Exupéry Offline #5 2011-06-09 news That is why there is static noise in Linux microphone recordings.
Ensure that the clients and server share the same cookie file found under ~/.config/pulse/cookie. Please read the Arch documentation before continuing to post incorrect statements. –jasonwryan Jan 29 '15 at 19:01 jasonwryan is right, the wiki does state that alsa-utils is installed with Taste is the enemy of creativeness.PicassoPerfection is reached, not when there is no longer anything to add, but when there is no longer anything to take away.Saint Exupéry Offline #8 2011-06-17 Connection & authentication Since PulseAudio runs as a daemon as the current user, clients needs to know where to find the daemon socket to connect to it as well as a
See also MPD/Tips and Tricks#PulseAudio. You will get an error only if no daemon was running, otherwise no messages will appear. See also man pages for pax11publish and pulseaudio for more details. up vote 58 down vote favorite 20 Sometimes pulseaudio service stops and it doesn't restarts itself when I open an audio file with banshee or totem.